mitsumi protection of lithium ion batteries (two cells in series) mm1292 protection of lithium ion batteries (two cells in series) monolithic ic mm1292 outline 2-cell protection ics this ic is for protecting a lithium ion battery from overcharging, excess discharging, and overcurrent. if abnormalities occur during charging and excess voltage is applied, it has a function that turns off the external fet switch when voltage is applied to each battery beyond a specified time (overcharging detection). it also has a function that turns off the external fet switch when the voltage for each battery falls below a set voltage, to prevent excess discharge when discharging the battery (discharging detection). at that time, the ic is switched to low current consumption mode. also, when there is a large current flow due to shorting or other reasons, there is a function for turning off the external fet switch (overcurrent detection). these functions comprise a protection circuit, with few external parts, for lithium ion batteries. model name overcharge protection overdischarge protection overcurrent detection voltage hysteresis detection voltage hysteresis detection voltage mm1302a 4.250.05v 10mv 2.3v0.1v 700mv 22020mv mm1292c 4.250.05v 200mv 2.4v0.1v 600mv 15015mv mm1292d 4.350.05v 200mv 2.4v0.1v 600mv 15015mv mm1302e 4.100.05v 10mv 2.4v0.1v 600mv 15015mv mm1302f 4.350.05v 10mv none none mm1302g 4.21535v 10mv 2.3v0.1v 700mv 22020mv mm1292h 4.300.05v 220mv 2.05v0.1v 950mv 17015mv mm1292j 4.250.05v 220mv 2.4v0.1v 600mv 15015mv mm1292k 4.250.05v 220mv 2.4v0.1v 600mv 15015mv mm1292l 4.250.05v 220mv 2.2v0.1v 800mv 10010mv features 1. current consumption (during overcharging) v cell =4.5v 80a typ. 2. current consumption (normal) v cell =3.5v 13a typ. 3. current consumption (during excess discharging) v cell =1.9v 0.5a typ. 4. current consumption (during excess discharging) v cell =1.0v 0.1a max. 5. overcharge detection voltage (ta= - 20c~+70c) 4.25v50mv (detection for each cell) 6. hysteresis voltage 200mv60mv (detection for each cell) 7. excess discharge detection voltage 2.4v0.1v (detection for each cell) 8. discharge resumption voltage 3.0v0.1v (detection for each cell) 9. overcurrent detection voltage 150mv15mv 10.reset after overcurrent detection load release 11.operating limit voltage 0.9v max. package sop-8c, sop-8d(mm1292 f) * the box represents the rank resulting from the combination of protection functions.
mitsumi protection of lithium ion batteries (two cells in series) mm1292 pin assignment 14 3 2 85 6 7 sop - 8c/sop-8d 1 oc 2 gd 3 n.c 4 gnd 5 td 6 vl 7 cs 8 vh pin description pin no. pin output function 1 oc output 2 gd output 3 ds input 4 gnd input 5 td input 6 vl input 7 cs input 8 vh input output pin for control of the charging control fet. when voltage detected between vh-vl or vl-gnd goes over overcharge detection voltage (valm), the output pnp- tr (open collector output) is switched on, and charging is prohibited by activating the element (npn-tr, or n-ch fet) that switches the charging control fet to off. this operation continues until the voltage falls below valm. output pin for driving the discharge control fet. when voltage detected between vh- vl and vl-gnd goes over excess discharge voltage (vs), this pin goes h. when voltage detected between vh-vl and vl-gnd falls below vs and the voltage between cs-gnd is more than the voltage detected for an overcurrent (vcs), it goes l. input pin for discharge detection. when voltage between ds-gnd during charge detection exceeds discharge detection voltage (vds), oc output is switched off and charge control fet is switched on. negative connection pin for the low side battery. it is also the gnd pin for this ic. (the ic's reference power supply pin.) over charge detection output non-induction time setting pin. the capacitor connected between td-gnd is charged with constant current (itc) during over charging. when tc pin voltage exceeds the threshold value (vtc), oc output is switched on. positive connection pin for the low side battery, and negative connection pin for the high side battery. overcurrent detection pin during discharge, and charging detection pin during power down. it detects discharge current using the source drain voltage (voltage between cs-gnd) of discharge control fet. also, when the battery is charged with a current whose cs-gnd voltage after power down exceeds the start-up voltage (vst), the bias current is drained to the interior circuit and operating status results. positive connection pin for the high side battery, and the ic's current input pin. applications 1. cellular phones 2. movies
mitsumi protection of lithium ion batteries (two cells in series) mm1292 block diagram note 1. 45a max. (current consumption during operation of overcharge detection section) flows to input protection resistor r1. note 2. 0.3a max. (when cells are balanced) flows to input protection resistor r2. when the cells are not balanced, the current increases to wards correction. data intake prohibition interval data intake prohibition interval t2 t1 top tst operating interval waiting interval top tst time average current 30 a 5 a current consumption current consumption timing for setting non-induction time v cell >4.25v v cell <4.25v data processing section non-induction time overcharging identification reset vh gc vcs (battery - )
mitsumi protection of lithium ion batteries (two cells in series) mm1292 timing chart oc td overcharging identification data latch hold untill t (n+1) overcharging detection output operation starts start-up signal generation timing and process discharging state gd vl vh vs vs vs v alm v alm v alm v alm v alm operation stop discharging prohibited vs unsettled (high impedance) current consumption or processing charging prohibited, constant current output (source current) unsettled absolute maximum ratings item symbol rating units storage temperature t stg - 40~+125 c operating temperature t opr - 20~+70 c power supply voltage v oc max. - 0.3~18 v oc pin applied voltage v ovout - 10~v h v cs pin applied voltage v dcout - 0.6~v h v allowable power dissipation pd 300 ma
mitsumi protection of lithium ion batteries (two cells in series) mm1292 electrical characteristics (unless otherwise specified, ta=25c) item symbol measurement conditions min. typ. max. units current consumption 1 i vh 1v cell =4.5v, r oc =270k 80 100 a current consumption 2 i vh 2v cell =3.5v (normal) 13.0 20.0 a current consumption 3 i vh 3v cell =1.9v (during excess discharge) 0.5 0.8 a current consumption 4 i vh 4v cell =1.0v (during excess discharge) 0.1 a vl pin input voltage i vl v h =v l - 0.3 0 0.3 a overcurrent detection voltage v alm ta= - 20c~70c 4.20 4.25 4.30 v hysteresis voltage v al v al =v almh - v alml 140 200 260 mv overcharge detection voltage v s 2.30 2.40 2.50 v discharge resumption voltage v df discharge resumed through voltage rise 2.90 3.00 3.10 v starting voltage v st voltage applied between gnd-cs pins - 0.6 - 0.5 v gd pin output voltage h v gdh v cell =3.5v, i l =10a vh - 0.3 vh - 0.2 v gd pin output voltage l v gdl v cell =3.5v, i l =10a, v cs =1v 0.2 0.3 v oc pin output current i och v cell =4.5v 20 150 a overcurrent detection voltage v cs 135 150 165 mv reset by overcurrent load release overcurrent detection delay 1 t oc 11020ms overcurrent detection delay 2 t oc 2 between cs-gnd pins > 0.8v 30 100 s excess discharge detection delay t od 10 20 ms tc pin charge current i tc 1 305080na tc pin threshold value v tc v cell =4.5v, v tc =0 5v v oc =l h 3.65 3.90 4.15 v non-induction time for overcharge t oc c tc =0.012f 0.5 1.0 1.5 s operating limit voltage v opl 0.9 v note 1. for current consumption, it is assumed that high side cell voltage and low side cell voltage are identical. when the cell voltages differ, it is set by the higher voltage. 2. gd pin are high impedance when the current consumption is below the operating limit voltage. 3. when the circuit configuration calls for discharge resumption through charging, the discharge resumption voltage is 2.4v typ. description of operation [outline] this ic is used for protecting lithium ion batteries (two cell series connection type). overcharge detection, excess discharge detection, and overcurrent detection are built into each circuit. it controls the fet for discharge control and charge control (external n-mos fet). there are four major operating modes. 1. overcharge mode when the voltage between vh-vi and vi-gnd exceeds the overcharge voltage (v alm ). 2. normal mode when the voltage between vh-vi and vi-gnd exceeds the excess discharge voltage (v s ) and is less than the over charge voltage (v alm ). 3. excess discharge mode when the voltage between vh-vi and vi-gnd is less than the excess discharge voltage (v s ). 4. overcurrent mode when the voltage between cs-gnd is less than the overcurrent voltage (v cs ).
mitsumi protection of lithium ion batteries (two cells in series) mm1292 [operation] 1. excess discharge detection circuit the h cell excess discharge detection circuit monitors the voltage between vh-vl, while the l cell excess discharge detection circuit monitors the voltage between vl-gnd. when the voltage between vh-vl and vl- gnd exceeds vs, the operating state is maintained with bias current supplied from the bias circuit to the delay circuit, the output control circuit, the overcurrent detection circuit, and the overcharge detection circuit. when the battery current for either the h or l cell falls below vs, the current from the excess discharge detection circuit to the bias circuit is switched off. also, the capacitor connected to the delay circuit's comparator (cod) input pin is charged using constant current. when this falls below the cod's reference input potential, the bias current to output control and current to the bias circuit are switched off. the excess discharge delay time (tod) is set by the delay circuit and cannot be modified externally. when the bias circuit is in waiting mode, the hysteresis loop to the excess discharge detection circuit is switched off, and the detection voltage of the excess discharge detection circuit becomes discharge resumption voltage (vdch). when the battery is being charged and the voltage between cs-gnd during excess discharge mode falls below vst, however, start-up current is supplied to the bias circuit, and the hysteresis loop of the excess discharge detection circuit is connected. therefore, the excess discharge detection circuit detection voltage becomes vs. also, the overcharging detection circuit goes into waiting mode, so overcharging detection does not occur in overcharging mode. when the cell voltage of either the h or l cell exceeds v alm (one is excess discharging and the other is overcharging), the bias current is maintained in the overcharging detection circuit. therefore, the overcharging is maintained until the current falls below v alm . the timing (clock) for the waiting interval and operating interval is created by the timing generation circuit. in normal mode, the only blocks operating during the waiting interval are the input stages for the timing generation circuit and the data intake section. other blocks operate only during the operation interval. the operation interval and the waiting interval are set at a ratio of 1:10, reducing power consumption. the voltage detection resistance of the overcharge detection circuit is switched on and off by the detection section's sw circuit. therefore, current does not flow to detection resistors during waiting time, resulting in low current consumption during excess discharge mode. (operating sequence) bias current is supplied to the timing generation circuit and data intake section by the bias circuit of the excess discharge detection section during normal mode. the operation interval and the waiting interval are created by the timing generation circuit. during the operation interval, bias current is supplied to the excess charging detection circuit, and cell voltages of both the h and l cells are monitored. 2. overcharging detection circuit
mitsumi protection of lithium ion batteries (two cells in series) mm1292 cs-gnd voltage mode delay time below v cs normal mode - v cs ~vf overcurrent mode (normal) t oc 1 above vf overcurrent mode (short) t oc 2 (vf : voltage between built-in npn-tr and base emitter) when the cell voltage of either the h or l cell exceeds v alm , an overcharge detection signal is output to the data intake section, and a reset signal is prohibited from going to the data processing section. when more than two consecutive clocks of the excess charging detection signal are input to the data intake section, a determination is made that the overcharging detection signal has been properly input, and it is output to the next stage. this prevents noise and mistaken determinations of overcharging caused by excess cell voltage fluctuation. when the date intake section outputs the overcharging detection signal, the data charge section goes into operation. when more than two clocks of overcharging signals are input, this activates the latch on the overcharging signal. when the overcharging signal latch in the date latch section is activated, the next non-induction time circuit goes into operation. when this operates, the td pin is charged by constant current (itc). the td pin potential and the threshold value (vtc) are compared by the non-induction time circuit comparator. when td pin voltage exceeds vtc, the oc pin output stage becomes operable and oc pin output pnp-tr (open collector) is switched on. also, bias current is supplied to the timing generation circuit and the operation of the overcharging detection circuit is maintained. when discharge occurs during overcharge mode (gnd < ds pin), the discharge detection circuit charges the td pin and non-induction time is reset. when cell voltage falls below v alm and the overcharging detection circuit signal is off, the reset prohibition is lifted. the reset signal is sent to the data intake and data latch sections and the non-induction time circuit, and normal mode is reinstated. a diode is built in between the oc pin and gnd. when oc pin potential falls below gnd terminal vf, current flows from the oc pin. therefore, when battery pack voltage < |
